1/4/2024 0 Comments Elkay outdoor touch timer![]() ![]() If you have any further questions then please get in touch with us at Elkay Technical. This product is capable of handing all load types at 16A and also is able to withstand high start up currents of up to 160A for less than 80ms but only when it is doing the switching. It is therefore not advisable to isolate whilst the product is still in timing mode. Isolation should only be done when the load is off. Turning the isolator off when the heater load is still on is not advised as it will leave the relay on the closed position and mean that all the start up current on next power up will potentially damage the product. The time switch must be allowed to switch off via its relay before the power is turned off at the isolator as this is to protect the relay and the product. What you must remember though is that time switches use a relay to turn on the load and power off the load. We suggest installing the hose bib on the top panel and foot pedal on the bottom panel on models that have two panels.Yes you can isolate the product when not in use and this is strongly advised if used, for example, in a pub back garden for example to stop unauthorised people turning the heater on at night. The foot pedal will work in conjunction with your hose bib. If I have a hose bib already connected to my free-standing bottle filling station, can I also connect the foot pedal? This is a hands-free activation optional accessory that can be retrofitted to new and existing, outdoor, free-standing, tubular bottle filling station models. Can I install this foot pedal on my existing fountain that is already installed? The foot pedal accessory must be ordered separately as an add on and connected upon bottle filling station installation or attached to an existing compatible model. ![]() Can this foot pedal be installed on a new bottle filling station at the factory? All push buttons will continue to function as normal. The foot pedal adds a hands-free activation option for the bottle filler only. Does this foot pedal activate or deactivate additional dispense points on the bottle filling station? The foot pedal attachment is made from Type 316 stainless steel and has a powder-coated exterior to withstand the elements, like our outdoor bottle filling stations. Is the foot pedal weather and water resistant? Freeze-resistant drinking fountain models require a specific push button and valve that are not yet compatible with this foot pedal. Does the foot pedal work with freeze-resistant, free-standing bottle filling station models? It is easy to install and does not deactivate the traditional push button. Elkay’s outdoor foot pedal accessory provides the option for hands-free bottle filling activation on select outdoor bottle filling stations. Is there a hands-free activation option for outdoor tubular bottle filling stations? Please see our care and cleaning instructions for specifics. Elkay 560A-1 Touch Outdoor 3-Wire Touch-Activated Timer (39533) Product rating 3.8 out of 5 stars 2 mins to 2 Hours IP66 Manual Override Facility Was 67.95 Save 10.00 (14) 57.95. How should I clean my outdoor fountains and/or bottle-filling stations?Ĭleaning procedures vary based on material. Elkay 560A-1 Touch Outdoor 3-Wire Touch-Activated Timer (39533) Product rating 3.8 out of 5. By totally isolating water supply circuits and valve systems, the sealed freeze valve system continues to function properly even if the water table level rises above the valve. At the start of the next cycle, an internal piston forces the stored water out into a dedicated drainage circuit above ground level. ![]() During operation, the sealed freeze valve pulls water down from above the frost line and stores it in an isolated chamber until the next drink cycle is started. If soil conditions do not allow for proper drainage, the ground water can back up into the valve area and prevent the valve drain system from working properly.Įlkay's sealed freeze valve system isolates the water removed from the upper plumbing lines. It drains the water into a drainage field. What is the difference between traditional freeze valve systems and our sealed freeze valve systems?Ī traditional freeze valve system relies on the gravitational flow of water down through the supply tubes. This action minimizes the chance of the water supply tubing freezing. Freeze-resistant fountains and bottle fillers drain the water from tubing above the frost line when the units are not in use. For pedestal installations, this is accomplished by installing the control valves underground below the frost line. Type 316 is commonly used in many industrial applications involving processing chemicals, as well as high-saline environments such as coastal regions and outdoor areas where deicing salts are common.įreeze-resistant units minimize the time incoming water spends in freezing temperatures. Unlike Type 304 stainless steel, marine-grade Type 316 stainless steel incorporates molybdenum, which significantly increases corrosion resistance. What makes Stainless Steel Type-316 the best base material choice?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |